We buy, sell and rent general purpose, optical and RF test and measurement equipment. We pay top dollar for your unwanted, surplus or defective gear. Let us make you an offer on your new or used Agilent, Tektronix, Anritsu, Fluke, Rohde & Schwarz and IFR instruments.
You are bidding on an Anritsu MS4623C 10 MHz - 6 GHz Vector Network Analyzer. It will arrive with a fresh calibration performed by an ISO 17025 accredited lab.
The Anritsu MS4623C 6 GHz, 2-Port Vector Network Measurement System / Direct Receiver Access with direct access to the receivers (i.e. without an integrated test set). This vector network analyzer offers the ultimate flexibility for power amplifiers, frequency translating, and multiple output device requirements.
Specifications:
Frequency Range: 10 MHz to 6 GHz. Source Power Range (No Options): +7 to 85 dBm. Level Accuracy:±1 dB. Sweep Range: 20 dB Minimum. Harmonics: 30 dBc. Stability: <5 ppm / year. Receiver Average Noise, 10 Hz: 115 dBm (<3 GHz), 105 dBm (3 to 6 GHz). Receiver 0.1 dB Compression: +7 dBm. Receiver Maximum Input: +27 dBm. Receiver Damage Level: +30 dBm. System Dynamic Range (Terminated): 125 dB (10 to 3000 MHz), 110 dB (3000 to 6000 MHz). High Level Noise: <0.008 dB rms (10 to 3000 MHz),<0.018 dB rms (3000 to 6000 MHz). IF Bandwidth Range: 10 Hz, 30 Hz, 100 Hz, 300 Hz, 1 kHz, 3 kHz, 10 kHz, and 30 kHz. Data Points: 1, 3, 15, 51, 101, 201, 401, 801, and 1601; Arbitrarily use Discrete Fill for 2 to 1601 points. Impedance: 50 Ohms. Frequency Resolution: 1 Hz. Power Output Range Source 1 (2-Ports No Options): +10 to 85 dBm (10 MHz to 3 GHz), +7 to 85 dBm (10 MHz to 6 GHz). Power Control Range: >20 dB. The minimum absolute level for power sweep is -15 dBm while the maximum power output for a unit is typically +10 dBm, depending upon configuration. Power Level Accuracy: ±1 dB to 6 GHz (no flat power calibration applied; full-band frequency sweep at -15 dBm, 0 dBm, and maximum rated power). Sweep Type: Linear, CW, Marker, or N-Discrete point sweep. Liquid Crystal Display: A Color 8.4" Thin Film Transistor (TFT) LCD display.
OPTIONAL:
1 Rack Mount
3 Internal 2nd Source / 3rd Test Port / Test Attenuator
11 Default Connector - Type N(F)
13 Intermodulation Distortion Measurements
24 Processing Upgrade: Adds processing upgrades for (1) additional data points (from 401 to 1601) when performing balanced/differential measurements on 3-port devices, (2) S4P file use in embedding/deembedding matching circuits, (3) additional throughput enhancements.
This unit is in excellent condition, has been fully tested and is guaranteed functional. It comes with a 30 day right of return should it not perform to your expectations. Please review pics and text carefully before bidding to verify accuracy of description. If you don't see it in the pictures, it is not included.
Insurance is included in UPS shipping charges. Item shipped internationally on buyer's UPS, FEDEX or DHL accounts only.
We will accept payment for this item by company check, cashier’s check and wire transfer only.
If you have zero feedback, contact us prior to purchase so we know you are a serious bidder. Otherwise, we may cancel your bid before the auction closes. It should be obvious that you should only bid if you are serious and do intend to complete the transaction. Any stated warranty will be voided if the unit is opened or if any calibration or lockout stickers have been tampered with or removed.
Please note that shipping and insurance costs are non-refundable.
Our feedback is very important to us and we strive for 100% positive on every transaction. If you are unsatisfied with any aspect of your transaction, please contact us before leaving negative or neutral feedback so that we can address and remedy the issue immediately. Additionally, we are always happy to leave positive feedback for our trading partners after a successful transaction.
Make sure that you check out our other auctions for more great deals on test and measurement equipment.
Thank you and good luck bidding.
Need your unit calibrated by an ISO 17025 accredited lab prior to shipment? Not a problem. We work with numerous calibration and repair companies that can provide your required service at competitive prices.
Spaulding Surplus, LLC was established in 2002 and we pride ourselves on sustaining an expansive and diverse inventory of high value test equipment, in stock and ready to ship. We strive to exceed our customers expectations by providing quality general purpose electronic test and measurement equipment at the absolute lowest prices around. Our equipment is sourced from a variety of manufacturers including Agilent/HP, Fluke, Tektronix, Rohde & Schwarz, LeCroy, Anritsu, Advantest, Aeroflex/IFR, ILX Lightwave, JDSU, Wavetek, etc. We are also dedicated to providing fair and competitive bids for your unused test equipment and excess inventory. WHY PAY MORE FOR THE SAME EQUIPMENT?
We accept payment by company check, bank transfer and Paypal (for items valued below $1500 USD). Payment must be received within 5 days of close of auction. Our mailing address is below and our bank info can be forwarded upon request. Spaulding Surplus 12829 Landale Street Studio City, CA 91604.
All instruments are professionally packed and shipped via UPS GROUND with full insurance. We typically ship within the continental US only (please no PO Boxes) unless other arrangements have been made with the buyer. International customers may provide their UPS, DHL or FedEx account for international shipments. Items will be shipped within 7 business days of payment.
All items sold on Ebay come with a standard 30 day right of return warranty from the date of receipt, unless otherwise specified in the auction details. Payment in full is required prior to shipment. Buyers are required to notify us immediately if an instrument arrives damaged, and must keep all boxes and packing materials in case a UPS damage inspection is necessary. An extended warranty of 30 days is available for all direct purchases from Spaulding Surplus, LLC and established customers purchasing directly may qualify for net 30 payment terms with PO required prior to shipment.
Spaulding Surplus typically offers a 30 day right of return for equipment received damaged or non-functional. However, Spaulding Surplus, LLC shall not be held liable for any damages resulting from buyer/operator negligence, or the improper use of its equipment, nor does it warrant their suitability for any specific application or project. The verification of product capability is the sole responsibility of the buyer. PO's and purchases cancelled due to insufficient instrument capability, buyer's remorse or loss of order are always subject to a minimum 20% restocking fee. A complete evaluation is required for any instrument returned under warranty, and refunds are not issued until said evaluation has been completed by an ISO 17025 accredited calibration lab.
Spaulding Surplus, LLC prides itself on sustaining an expansive and diverse inventory of high value test equipment, in stock and ready to ship. We strive to exceed our customers expectations by providing quality general purpose electronic test and measurement equipment at the absolute lowest prices around.
